About Wrap Guys America

Great Pricing
1/2 Wraps from $495 Full Wrapsfrom $1395

Wrap Guys America is a vehicle and building wrap company that designs, prints, and installs custom vinyl wraps. We work out of an indoor shop in Kirkland, Washington, and we wrap vehicles for customers across Washington and Oregon as well as in California cities including Los Angeles, San Diego, and San Francisco.

Over 25 Years of Vehicle Wrapping Experience

We have been wrapping vehicles since 1999, which puts more than 25 years of installs behind the work we hand back to you today. In that time, the film has changed, the printers have changed, and the vehicles have gotten a lot harder to wrap, with deeper body lines and more sculpted bumpers than anything we saw in our first decade. What we learned early has held up: a wrap is only as good as the hours spent on the parts nobody photographs.

That experience shows up as judgment. Knowing how far a piece of cast vinyl will stretch across a fender before the color starts to look thin, or how to lay film into a deep recess without tension building behind it, is not something you get from a spec sheet. You get it from doing it thousands of times.

Wrap Guys America vinyl wrap project

Serving an Area Near You

Our shop is at 105 - 11335 NE 122nd, Kirkland, WA, and every wrap we install goes on indoors there. That matters more than most people expect. Vinyl adhesive has a temperature range where it behaves: too cold and it stiffens and refuses to bond cleanly at the edges; too warm and it grabs before you have had a chance to position the panel. A controlled, dust-free bay takes that variable off the table.

From Kirkland, we serve customers throughout the Puget Sound region and down the I-5 corridor, including Seattle, Bellevue, Everett, Tacoma, Olympia, Kent, Bellingham, Spokane, and Portland. Don’t see your city listed here? Find out if we serve an area near you.

Vinyl Wraps That Get Your Vehicle Noticed

A wrapped work truck advertises on the way to the job site, in the parking lot, and at every red light in between, and it keeps doing it long after a print ad or a radio spot has stopped running. That is the whole idea we built the shop around: your business should not need a media budget to get in front of thousands of people every week.

The same care goes into a single owner-operator's pickup as goes into a multi-vehicle fleet rollout. Same film, same prep, same inspection.

Our Wrap Design and Installation Process

  1. Consultation and design: We work through your logo, colors, imagery, and message, then send a digital proof so you can see the wrap on your actual vehicle before anything is printed.
  2. Printing: Your approved design goes onto 3M or Avery cast vinyl and gets a UV-protective laminate layer that keeps the color from fading in direct sun.
  3. Prep: The vehicle is washed, decontaminated, and wiped down so nothing sits between the paint and the adhesive. Wax, road film, and polish residue are the most common reasons a wrap lifts early, and we do not skip past them.
  4. Installation: We apply the film panel by panel, heating and shaping it around curves, handles, and mirrors, then post heat every edge and recess so the vinyl stays where we put it.
  5. Inspection: Before the vehicle leaves, we go over it, panel by panel, and hand it back with care instructions, including the 24 to 48 hours we ask you to wait before the first wash.

Our Materials and Warranty

We wrap in 3M or Avery cast vinyl with a UV laminate, the grade of film the industry relies on for long-term outdoor work. Cast film is thinner and more stable than calendered film, so it conforms into recesses and around curves without fighting to shrink back later.

Every car wrap we install carries a 7-year warranty, and our wraps typically last at least nine years in service. We have been called in often enough to strip and redo other people's work to know what shortens that life: edges never post heated, film overstretched across curves, dirt trapped under panels that were washed but never decontaminated, and seams that break where two doors meet.

You Name It, We'll Wrap It

Concrete pump vinyl wrap by Wrap Guys America

Not sure whether the project you have in mind is something we can handle? It probably is. We have wrapped trailers, concrete equipment, boats, jet skis, and a long list of odd shapes that never came with an installation manual. Tell us what you are looking at and we will tell you whether vinyl is the right answer.

View Special Wrap Projects

Request a Quote:

You need a vehicle wrap designed for getting your business noticed and generating leads. Let the pros at Wrap Guys help. Let's chat! 1-360-329-5413
Let's connect!

We love meeting new friends.

Thank you! Your message has been sent.
An error occurred, please fill in all fields correctly.

Required fields indicated with a red star

Request a quote